Product information

This product supersedes product no: 757395

Specification

Approvals

• This composition meets the criteria for not being harmful to the marine environment according to MARPOL Annex V and may be discharged into the sea when used to clean cargo holds and external surfaces on ships.

Directions for use

To achieve optimal protection the cargo hold surfaces should be as clean and dry as possible before treatment with Unitor™ Slip Coat Plus™. NOTE! After cleaning with sea water, holds should always be flushed with fresh water before applying Unitor™ Slip Coat Plus™. The ready-to use concentration makes it ideal for application directly from the Chemical Applicator by use of the Unitor™ Panamax Cargo Hold Cleaning Kit™ and correct application nozzle.

Do not apply more than necessary, one single application is sufficient and will cover 10--20 m2/ltr depending on the condition of the cargo holds. Start applying Unitor™ Slip Coat Plus™ from top and downwards. Allow the film to dry completely before loading the cargo a process which takes 1-2 hours depending on air and surface temperature and humidity.

Note that larger amounts of Unitor™ Slip Coat Plus™ may end up at tank top when holds are sprayed. Ensure that only a thin layer is applied on the tank top. Avoid larger amount of Unitor™ Slip Coat Plus™ and remove excessive remaining for optimal result. For removal of excessive Unitor™ Slip Coat Plus™ on tank top it is recommended to use the Unitor™ VCAD 200 (682054). Flushing away excessive amounts of Unitor™ Slip Coat Plus™ with fresh water is also possible before drying.

After drying, Unitor™ Slip Coat Plus™ creates a dense, non-sticky film on the cargo hold surfaces. After cargo discharge, both the film and cargo residues are easily removed by the use of an alkaline cleaner like Unitor™ Aquatuff™ or Unitor™ Aquatuff High Foam™. A minimum 10 % solution in fresh water is recommended, leave for 15-30 minutes, re-soak with Unitor™ Aquatuff High Foam™ to keep surface wet during soaking (avoid surface to dry), and finally flush with clean high pressure water. After flushing with water, let the surfaces dry and then repeat the treatment with applying Unitor™ Slip Coat Plus™ before the next cargo.

Note! The lowest surface temperature when applying Unitor™ Slip Coat Plus™ is +5 Celsius

Note! Maximum temperature for surfaces and cargo should not exceed +70 Celsius

Always follow paint manufacturer recommendations and always allow paint to cure before applying cargo or chemicals.

产品特点

• 防水货舱屏障

• 即买即用- 一个单一的应用程序

• 所有涂料都完全安全

• 可使用碱性清洁剂轻松移除

• 水溶性- 不含烃类溶剂

• 基于FDA列出的成分的组合物

优势

• 对所有表面都有出色的附着

• 适用于潮湿和腐蚀性货物
，如硫磺
，盐等。

• 防止最难清洗的货物也能粘附在涂层上

• 节省清洁时间和清洁化学品

• 提供临时防腐蚀保护

订购信息

Product Number             Product name

778865                    SLIP COAT PLUS 25 LTR

认证

• 根据MARPOL附则V

，该组合物符合不对海洋环境有害的标准，并且当用于清洁货舱和船舶外表面时可以排入海中

。

使用说明

为了获得最佳保护
，在使用Unitor™Slip Coat Plus™处理之前，货舱表面应尽可能干净和干燥。注意！在使用海水清洁后，在使用Unitor™Slip Coat Plus™之前
，应始终用清水冲洗。即用型浓缩液使其成为直接应用于化学品的理想选择

涂抹使用Unitor™ Panamax Cargo Hold Cleaning Kit™和正确的喷嘴.

D不要超过必要的应用量
，一次单独的应用就足够了，根据货舱的状况将覆盖10-20平方米/升。从顶部和向下开始使用Unitor™Slip Coat Plus™。在装载货物之前，让薄膜完全干燥，这需要1-2小时，具体取决于空气和表面温度和湿度
。

请注意，喷涂固定装置时
，较大量的Unitor™Slip CoatPlus™可能会最终落在罐顶。确保在罐顶上仅涂抹薄层
。避免使用大量Unitor™Slip Coat Plus™并去除过量残留物以获得最佳效果
。为了去除罐顶上过多的Unitor™SlipCoat Plus™，建议使用Unitor™VCAD 200（682054）。

在干燥之前，也可以用淡水冲洗掉过量的Unitor™Slip Coat Plus™

干燥后，Unitor™Slip Coat Plus™在货舱表面形成致密
，不粘的薄膜
。货物卸货后
，通过使用碱性清洁剂（如Unitor™Aquatuff™或Unitor™Aquatuff High Foam™）可轻松去除薄膜和货物残留物
。建议使用至少10％的淡水

溶液，保持15-30分钟
，使用Unitor™Aquatuff High Foam™重新浸泡
，以在浸泡过程中保持表面湿润（避免表面干燥），最后用干净的高温冲洗压力水。用水冲洗后，让表面干燥，然后在下一批货物之前使用Unitor™Slip Coat Plus™重复处理。

注意！使用Unitor™Slip Coat Plus™时，最低表面温度为+5摄氏度

注意！表面和货物的最高温度不应超过+70摄氏度始终遵循涂料制造商的建议

并且在使用货物或化学品之前始终确保油漆固化。